City of Jurupa Valley (CA)

California Authority Having Jurisdiction Solar permitting requirements

NEC Code Version2023

Fire Code Version2018 Building Code

SolarAPP+ StatusAdopted

Wet Stamps RequiredDigital Structural

Fire Setback Enforced1

Codes

NEC Code Version: 2023

Fire Code Version: 2018 Building Code

Code List

2025 CALIFORNIA BUILDING CODE

2025 CALIFORNIA ELECTRICAL CODE

2025 CALIFORNIA FIRE CODE

2025 CALIFORNIA PLUMBING CODE

2025 CALIFORNIA MECHANICAL CODE

2025 CALIFORNIA ENERGY CODE

2025 CALIFORNIA RESIDENTIAL CODE

2025 CALIFORNIA ADMINISTRATIVE CODE

IEBC Accepted: 1

ASCE Code Specification: ASCE 7-16

SolarAPP+ & submittal

SolarAPP+ Status: Adopted

Any SolarAPP+ Restrictions: 1

SolarAPP+ Restrictions: Existing Systems,Trenching

How Many Plansets Required: 3

Revision Required: 1

New Planset Required For Module Swap: 1

Stamps

Ee Stamp Required On SLD: Yes - 10kW+,Yes - Derate

Wet Stamps Required: Digital Structural

Structural Calculations Required: Yes

Ee Stamp Notes

EE stamp required for systems over 10kW
EE stamp required for derates

Stamp Location On Plans: Unspecified

Date On Stamps: Expiration Date

Fire setbacks

Fire Setback Enforced: 1

Setback Notes: Standard

Structural & loads

Wind Speed: 110

Wind Notes

Review the installation address on a map

West of Van Buren blvd = 130 mph

East of Van Buren blvd = 110 mph

All Regions = Exposure Category C

Snow Load: 0

Snow Load Notes: N/A

Reducible Snow Load Allowed: 1

Max Attachment Spacing: 48

Structural Notes

ASCE Design Hazards Report showing wind and snow hazards is required
MUST INCLUDE BATTERY MOUNTING CALCULATIONS ON STRUCTURAL CALCS
Any project the pertains to the City of Jurupa Valley, must have a Jurupa Address on it. Even if Google Maps says otherwise. Project address CANNOT reflect City of Riverside, Eastvale or Mira Loma even if that's the address that appears on Google. If the project is located within zip code 92509, or 91752 it belongs to city Jurupa Valley

Minimum Ground On Roof: #10

Electrical

Electrical Load Calcs Required: Derates

Allowed POI: Line Side Taps,PV Breaker,Load Side Taps,Meter Adapter

Panel Schedule Required: Partial Home Backup

Temperature Rating: 90

De Rating Ampacity: 0.91

BOS Restrictions: Standard

Battery / ESS

Unique Battery Placards Needed: 0

ESS Notes

All Jobs

ESS disconnect required within 6ft of Battery on same wall and not blocked by walls/gates/etc

Cover page must have a brief scope of work regarding battery system details -- Example:

Battery: Manufacturer

Capacity: __kW (charge rate) __kWh (capacity)

Purpose: Whole Home Backup/Partial Home Backup/Self-Consumption (Non-Backup)

Include sub panel details if applicable (i.e. (N) 125A SUB PANEL)

Backup

Backup Load Panel MUST be labeled 'sub panel'
Include sub panel in scope of work (Title Block)

Separate ESS Disconnect Required: ESS Disconnect

ESS Elevation Detail Required: Yes - with dimensions

Plan set

Plan Set Requirements

Some addresses MUST be manually updated to reflect Jurupa Valley

Any project that will be submitted to City of Jurupa Valley, must have a Jurupa Address on it. Even if Lightspeed, or utility bill shows another city.

Project address CANNOT reflect City of Riverside, Eastvale or Mira Loma if submitting to Jurupa Valley.
If it falls in zip code 92509, or 91752 it belongs to city Jurupa Valley
This must be updated on all areas that reflect the address (Vicinity map, title block, etc.)

Address in both plans and structural calculations must match, and show Jurupa Valley

Cover Page

APN must be listed on title block

Must include brief Scope of Working showing proposed system details

System size

MPU rating & main breaker rating (if applicable)

Site: All structures must be clearly labeled

Roof Plan

ENHPASE

Must show micro-inverters on each panel

Call out combiner panel location

Existing systems

THE LAYOUT OF EXISTING PV SYSTEMS NEED TO BE ILLUSTRATED AS INDIVIDUAL MODULES, NOT ONE BIG 'OBSTRUCTION'

Layout of modules needs to be replicated in Aurora before downloading DXF

The AHJ requires (E) system details to be accurate to their records, ensure we have detailed information about the (E) system before proceeding

Module, Inverter (type, wattage, qty)
If (E) system uses micros, we must show that on the roof plan

The module coverage calculation must include existing systems (if applicable)

Attachment Detail: West of Van Buren - Use 4' o.c. attachment spans

Electrical Diagram

MPU

Include the (E) and (N) Service Panel Amperage, to show what we are upgrading from

The AHJ requires (E) system details to be accurate to their records, ensure we have detailed information about the (E) system before proceeding

Module, Inverter (type, wattage, qty)
Include accurate wiring illustration of (E) system

Electrical Diagram Notes

Custom Placards Required: 0

Non Standard Revision Requirements

Clouding/Deltas/Revision letter MUST ONLY pertain to the most recent changes. We cannot include clouds or notes about previous changes.
Revision letter must specifically state changes made.
Cannot use abbreviations like BOS, etc.

Ground mount

Ground Mount Fencing Required: Yes

Ground Mount Notes: Ground Rod Required at ground mount panel installation. Please add to plan on single line and three line diagram